1992 Baltic 5216m

CONSTRUCTION

RCD Status:                                                                               

• Our understanding is that the yacht is exempt from CE Confirmity as she was in use in the EEA prior to June 1998.

Hull Construction:

• Fiberglass and balsa sandwich construction, E-glass hybrid fibers and CK57 aircraft balsa laminated with Isophthalic polyester resin, post cured and vacuum bagged
• Hull painted
• All high stress areas are specially strengthened with built up unidirectional roving orientated in the direction of the stress.
• Uni-directional roving is a special developed glass/ aramid hybrid to improve impact resistance, strength, stiffness and safety of the structure.
• High grade epoxy resin is used in the lamination process to create an extremely strong high-tech laminate.
• Transverse floors and longitudinal stringers are made up of uni-directional roving and fabmat around a low density PVC core.
• Main structural bulkheads are built up of a balsa core GRP sandwich construction.
• Chain Plates are stainless steel through bolted to longitudinal or transverse bulkheads which are securely bonded to the hull and deck. Plates are provided with backing plates to spread loads adequately. Chain plates are grounded to a keel bolt for lightning protection.
• Engine beds are incorporated in hull. Built up of uni-directional fibers on a PVC foam core.
• Fabricated aluminium alloy mast step bolted to re-inforced floors and stringers.

Deck & Superstructure Construction:

• Hand laid-up moulded fiberglass with balsa core for stiffening and insulation, appropriate reinforcement incorporated in the area of the winches and fittings.
• The deck has a high strength/ weight ratio and is bonded to the hull with layers of roving. The deck is through bolted to the hull.
• Hand laid teak deck including cockpits and aft coamings – replaced 2006

Keel & Rudder:

• Fin keel, lead with antimony
• Stainless steel cast-in keel bolts.
• Balanced spade rudder, Epoxy/S-glass both blade and shaft
• Rudder bearings

MACHINERY

Engine & gearbox:

• Yanmar 4JHZ-UTE 4-cylinder turbo-charged diesel engine producing 100hp @ 3600 rpm
• Engine hours – approx 5,300 as of end of 2021
• Yanmar reduction gearbox
• Fresh water cooled engine.
• Single lever engine control.  

Propulsion & Steering:

• 24vDC bowthruster
• 5-bladed feathering propeller
• Stainless steel ‘destroyer’ type helm wheel with Baltic Yachts custom made pedestal.
• The steerer has sprockets and non magnetic chains leading to steering cables. The steering cables are stainless steel wire and the cable sheaves have a score diameter of not less than 20 times the wire diameter. The steering sheaves are mounted on brackets securely bonded to the structure – steering cables replaced during 2017/18 refit
• One aluminium alloy tube emergency tiller, storage in cockpit locker.
• Aquadrive drive shaft antivibration system – 2015

ELECTRICAL SYSTEMS

Voltage systems:

• 24vDC domestic systems with 220vAC via shore-power, generator or inverter
• Electrical system revised
• 24v-12v KD60 voltage converter

Battery Banks:

• 12vDC engine start battery
• 12vDC generator start battery
• 24vDC service batteries
• Battery monitoring system

Charging / Inverter:

• Quick Advanced plus 140Amp Battery charger
• 3kw inverter

Generator:

• Lombardini 6kw diesel generator – 2014
• Generator hours – approx. 36 as of end of 2021

Alternator:

• 12v engine-mounted alternator for start battery
• 24v 175 Amp secondary alternator for service battery bank

Other Electrical:

• Baltic Yachts custom made with automatic safety circuit breakers. Indication diodes, amp.meters, volt meters and tank level meters are provided. A 12 V DC for starting system, 24 V DC for service system.
• 220vAC Shore power
• Interior electric partially replaced custom circuit

PLUMBING & GAS SYSTEMS

Fresh Water:

• Water heater provided. Heated by engine cooling water and shore power.
• 60 litre hot water tank
• Water pressure system with outlets in heads and galley. Pump with automatic pressure switch.
• Telephone type shower, water faucet for cold and hot pressurised water.

Watermaker:

• Reverse osmosis 100lt/h Schenker watermaker
• Serviced and never used from the actual owner

Bilge Pumps:

• Electric bilge pump
• 2x manual bilge pumps

TANKAGE

• All tanks are Baltic custom made in stainless steel with baffles and inspection covers.
• All tanks are pressure tested.
• Tank shut-offs provided. A water separator is installed on the fuel line. The fuel tank has a deck fill marked FUEL. The fill fitting is grounded via the tank to a keel bolt.
• The fresh water tanks have deck fill marked WATER.
• Tank meter with selector switch on electrical panel.
• The tanks are securely laminated to the hull and foamed in for rigidity and sound insulation.

Fuel:

• Approx 360 litres fuel capacity

Fresh Water:

• Approx 760 litres water capacity

Holding Tanks:

• Blackwater holding tank
• Holding tank level gauge at the chart table

NAVIGATION & COMMUNICATION EQUIPMENT

Chart table:

• B&G Hydra 2000 sailing instruments digital display
• Raymarine E80 chartplotter
• Raymarine ST60+ dislay
• Furuno GPS Navigator GP-31

Cockpit:

• Custom made autopilot
• B&G Hydra 2000 sailing instruments digital display
• Raymarine E80 chartplotter
• ST 7000 Autopilot - not working
• 5x B&G H2000 wind, speed and depth station
• 1x solar Raymarine wind display
• Steering compass

Communications Equipment:

• Raymarine RAY 215 E VHF with DSC

DOMESTIC EQUIPMENT

Galley:

• Technimpex gas stove with 3x burners and oven
• Top-loading fridges with 2x compressors
• Double stainless steel sink with pressurised hot & cold water
• Fresh and salt water foot pumps

Heads:

• 3x Jabsco electric heads
• Hot & cold pressurised water supplies with shower in heads

Heating & Ventilation:

• Air cabin heating system – removed, pipes still installed
• DC ventilation fans

ACCOMMODATION

Summary of Accommodation:

• The Baltic 52 sleeps 8 persons in 4 separate guest staterooms. 3 heads compartments

Forward Guest Cabin:

• Two guest cabins with twin bunks to port and starboard plus hanging locker
• Ensuite heads access.

Heads

• Moulded GRP basin in special hygienic gelcoat.
• Counter unit and lockers with ample provision for stowage.
• Foot-operated fresh water pump.
• Marine toilet with overboard discharge through seacock.
• Mirror, toothbrush, towel, soap and paper holder.
• Telephone type shower, water faucet for cold and hot pressurised water, shower sump with sump pump.

Main Saloon

• Dining area to port with dining table and U-shaped settee.
• Dining table fixed and hand-rubbed varnished teak.
• All visible wood surfaces are teak faced.
• Bookshelves and storage space provided.
• Settee provided to Stb.

Navigation Station

• Navigation area to starboard with stowage for charts, books, pencils etc.
• Forward facing chart table with upholstered seat
• Bulkhead space for mounting electronic instruments, radio equipment, etc.
• Master electric panel with safety circuit breakers and navigator's light.

Galley

• Aft of saloon to port
• Stowage for cooking utensils.
• Drawers and glass racks for stowage of crockery.
• Laminate covered work top with deep fiddles.
• Deep stainless steel sink units.
• Water faucet for hot and cold pressure water.

Aft Guest Cabin:

• Aft of navigation station to starboard
• Upper and lower bunks
• Hanging locker

Aft Shower:

• Shower compartment accessible from aft guest cabin and master cabin

Owner’s Suite

• King size berth, table with storage drawers under on each side.
• Toilet with shower cabin.
• Hanging lockers
• Dressing table

Owner’s Ensuite Heads:

• Accessible also from galley for use as day-heads
• Moulded GRP basin in special hygienic gelcoat.
• Counter unit and lockers with ample provision for stowage.
• Foot-operated fresh water pump.
• Marine toilet with overboard discharge through seacock.
• Mirror, toothbrush, towel, soap and paper holder.
• Telephone type shower, water faucet for cold and hot pressurised water, shower sump with sump pump.

Accommodation Finish:

• Joinery work is to the highest standard. All joinery is teak faced with solid teak or laminated teak frames and capping. The joinery is varnished throughout. Visible surfaces are varnished and handrubbed to obtain a satin type of surface.
• All doors are provided with retaining hooks and swing stops. Kick plates on steps and chafing pieces on sills are provided.
• Curtains are provided for side windows and portlights
• Hanging lockers are provided with rods and hooks.
• Locker doors are fitted with louvers for ventilation.
• Teak gratings in head.
• Floorboards with laid teak veneer. Access to bilge provided where practical. Dust collector with teak grating in front of main entrance ladder.
• Ceiling lined with removable soft panelling.
• Blue & white striped upholstery throughout

DECK EQUIPMENT

Rig:

• Reckmann alloy mast painted white – 2016
• 3-sets of inline spreaders
• Nitronic discontinuous rod standing rigging – replaced 2017
• Manual genoa furler
• Navtec hydraulic boom vang and backstay adjuster
• Cutter stay sail arrangement – stay sail cable not installed
• Harken Battcar system for mainsail
• Second main halyard sheave and halyard, also used for gangway
• Insulated backstay
• Checkstays
• Ubi Maior furling Code 0
• Carboway carbon fibre foldable bowsprit

Winches:

• 2x Barient B-737 3-speed primary winches
• 1x Barient B-28 self-tailing electric main halyard winch
• 2x Barient B-36 self-tailing powered secondary winches
• 2x Barient B-32 self-tailing genoa halyard winches
• 1x Barient B-32 self-tailing spinnaker halyard winch
• 2x Barient B-28 self-tailing control line winches – available but not installed on board
• 1x Barient B-24 self-tailing mainsheet winch

Sails:

• Millennium mylar-carbon fully-battened mainsail
• Millennium Dacron furling genoa
• Millennium Code 0  - 2016
• Millennium Gennaker - 2016
• Dacron main sail
• Dacron jib

General:

• A pulpit and pushpit of high quality stainless steel tube are mounted on the bow and transom.
• Double life lines are installed passing through stainless steel stanchions with stainless steel wire and set up with turnbuckles at the after end.
• The pulpit is fitted with navigation lights and the pushpit with a stern light.
• Stainless steel handrail for main companionway is provided.
• Passarelle
• Transom antenna pole for radar

Covers & Canvas:

• Navy blue stackpack for mainsail with lazyjacks
• Canvas helm wheel and pedestal cover
• Navy blue canvas sprayhood
• Cockpit cushions

Anchoring & Mooring:

• Lewmar 24vDC electric anchor windlass
• Anchor with chain
• Carbon fibre folding gangway
• Carbon fibre Swimming ladder

SAFETY EQUIPMENT:

General note on safety equipment: Any safety equipment such as liferafts, Epirbs, fire extinguishers and flares etc. are usually personal to the current owner(s) and if being left on-board as part of the sale of a used vessel may require routine servicing, replacement, or changing to meet a new owners specific needs.

Life saving:

• Self-inflating ring
• IOR self-inflating buoy
• Spare anchor
• Flares
• Self-inflating grab bag 12 people liferaft.

Grabau International (Italia) offers the details of all vessels in good faith but cannot guarantee or warrant the accuracy of this information or warranty the condition of any vessel and the details do not constitute a part of any contract. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. All vessels are offered subject to prior sale, price change, or withdrawal without notice. Grabau International (Italia) provides professional yacht conveyancing and legal transfer of title for all yachts as per the ABYA Code of Practice with all deposit payments and final balance payments processed through secure dedicated client accounts solely for that purpose. Our dedicated client accounts are written in trust at Natwest Bank and we are fully insured.